1 to 20 of  572 products for cable box remote control

Result for "cable box remote control"
Sony Universal Remote Control

Universal Remote Control - Width: 5.5" - Height: 1.5" - Depth: 11"

more >>
Sears
$10.09 See It
Solo/Cinemate Remote Universal Remote Control

Money-back Guarantee!

for use with Bose Solo TV sound system or CineMate home theater speaker systems,controls your TV and connected components such as a satellite/cable box, DVD player, and VCR,batteries included

more >>
Crutchfield
$29.99 See It
RPS-2325-72 - Migatron RPS-2325 Controller with Remote Sensing Head, 8"-72" range, (2) Iso

RPS-2325-72 - Migatron RPS-2325 Controller with Remote Sensing Head, 8"-72" range, (2) Isolated Form C Relay OutputsSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducerAdjustable delay controls2 independent range adjustmentsLED indicatorsIsolated Form C relay outputsSmall electronic controllerThe RPS-2325 is a single transducer device with 2 independent range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. The transducer head is constructed of 303 stainless steel with a 302 stainless steel sensing face making this unit best suited for environments where dirt is a problem, as well as some chemical environments. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time.This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor has a narrow sensing beam and operates at a frequency of 204kHz for the 14" and 36" ranges and 150kHz for the 72" range. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. Download the RPS-2325-72 datasheet in *.pdf format RPS232572

more >>
Walker EMD
$884.00 See It
RPS-2300-36 - Migatron RPS-2300 Controller with Remote Sensing Head, 5"-36" range, (2) Iso

RPS-2300-36 - Migatron RPS-2300 Controller with Remote Sensing Head, 5"-36" range, (2) Isolated Form C Relay OutputsSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducerAdjustable delay controls2 independent range adjustmentsLED indicatorsIsolated Form C relay outputsSmall electronic controllerThe RPS-2300 is a single transducer device with 2 independant range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. The transducer heads are made of Delrin with epoxy face for the 14" and 36" sensors and Valox with a silicon face for the 72". A sealed silicon rubber sensing face is used making this sensor best suited for environments where dirt is a problem. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves).With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor has a narrow sensing beam and operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. Download the RPS-2300-36 datasheet in *.pdf format RPS230036

more >>
Walker EMD
$585.00 See It
RPS-302-36T - Migatron RPS-302-T Controller with Remote Sensing Head, 5"-36" range

RPS-302-36T - Migatron RPS-302-T Controller with Remote Sensing Head, 5"-36" rangeThe RPS-302 has 2 sealed, multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals.These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor, operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. This sensor has a narrow sensing beam. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-302-36T datasheet in *.pdf format RPS30236T

more >>
Walker EMD
$971.00 See It
RPS-302-36 - Migatron RPS-302 Controller with Remote Sensing Head, 5"-36" range, Isolated

RPS-302-36 - Migatron RPS-302 Controller with Remote Sensing Head, 5"-36" range, Isolated Form C Relay for each TransducerSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducersAdjustable delay controls2 multiplexed transducersLED indicatorsIsolated Form C relay outputsSmall remote transducerThe RPS-302 has 2 sealed, multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals.These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor, operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. This sensor has a narrow sensing beam. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-302-36 datasheet in *.pdf format RPS30236

more >>
Walker EMD
$856.00 See It
RPS-2300-36T - Migatron RPS-2300 Controller with Remote Sensing Head, 5"-36" range

RPS-2300-36T - Migatron RPS-2300 Controller with Remote Sensing Head, 5"-36" rangeThe RPS-2300 is a single transducer device with 2 independant range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. The transducer heads are made of Delrin with epoxy face for the 14" and 36" sensors and Valox with a silicon face for the 72". A sealed silicon rubber sensing face is used making this sensor best suited for environments where dirt is a problem. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves).With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor has a narrow sensing beam and operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. Download the RPS-2300-36T datasheet in *.pdf format RPS230036T

more >>
Walker EMD
$653.00 See It
RPS-2100-72 - Migatron RPS-2100 Controller with Remote Sensing Head, 5"-72" range, (2) Iso

RPS-2100-72 - Migatron RPS-2100 Controller with Remote Sensing Head, 5"-72" range, (2) Isolated Form C Relay OutputsSpecifications:Various sensing rangesLow frequency - 38.5 kHz2-way power operationSmall remote transducer2 independent range adjustmentsLED indicatorsIsolated Form C relay outputsSmall electronic controllerThe RPS-2100 is a single transducer device with 2 independent range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another.There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor operates at a frequency of 38.5kHz, has a broad sensing beam which allows for detection of an object at greater angles of tilt. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. RPS210072

more >>
Walker EMD
$561.00 See It
RPS-302-14T - Migatron RPS-302-T Controller with Remote Sensing Head, 4"-14" range

RPS-302-14T - Migatron RPS-302-T Controller with Remote Sensing Head, 4"-14" rangeThe RPS-302 has 2 sealed, multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals.These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor, operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. This sensor has a narrow sensing beam. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-302-14T datasheet in *.pdf format RPS30214T

more >>
Walker EMD
$971.00 See It
RPS-2100-240 - Migatron RPS-2100 Controller with Remote Sensing Head, 10"-240" range, (2)

RPS-2100-240 - Migatron RPS-2100 Controller with Remote Sensing Head, 10"-240" range, (2) Isolated Form C Relay OutputsSpecifications:Various sensing rangesLow frequency - 38.5 kHz2-way power operationSmall remote transducer2 independent range adjustmentsLED indicatorsIsolated Form C relay outputsSmall electronic controllerThe RPS-2100 is a single transducer device with 2 independent range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another.There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor operates at a frequency of 38.5kHz, has a broad sensing beam which allows for detection of an object at greater angles of tilt. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. RPS2100240

more >>
Walker EMD
$572.00 See It
RPS-102-14 - Migatron RPS-102 Controller with Remote Sensing Head, 2"-14" range, 1 Isolate

RPS-102-14 - Migatron RPS-102 Controller with Remote Sensing Head, 2"-14" range, 1 Isolated Form C Relay Output for each TransducerSpecifications:Various sensing rangesBroad sensing beamLow frequency - 38.5kHz2-way power operationSmall remote transducersAdjustable delay controls2 multiplexed transducersLED indicatorIsolated Form C relay outputSmall electronic controllerThe RPS-102 has 2 multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board.One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located alongside the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent isolated form C relays furnish N.O. and N.C. outputs. This sensor, which operates at a frequency of 38.5kHz, has a broad sensing beam which allows for detection of an object at greater angles of tilt. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-102-14 datasheet in *.pdf format RPS10214

more >>
Walker EMD
$776.00 See It
RPS-302-14 - Migatron RPS-302 Controller with Remote Sensing Head, 4"-14" range, Isolated

RPS-302-14 - Migatron RPS-302 Controller with Remote Sensing Head, 4"-14" range, Isolated Form C Relay for each TransducerSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducersAdjustable delay controls2 multiplexed transducersLED indicatorsIsolated Form C relay outputsSmall remote transducerThe RPS-302 has 2 sealed, multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals.These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor, operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. This sensor has a narrow sensing beam. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-302-14 datasheet in *.pdf format RPS30214

more >>
Walker EMD
$856.00 See It
Gecko Spa 0603-409001 in.therm 4kW 240v Remote Heating System

Gecko Alliance Intelligent remote heater for in.xm control systems. 0603-409001     In.therm can be quickly installed. Its threads and in.link cables make it easy to connect to pack system and spa pipes.   Unlike any other heater on the market, in.therm was designed specifically to work with in.xm spa systems. An ode to plug & play, you only have to connect its in.link power and communication cables to their specific in.xm connecting ports to make it go. Heater must be installed with access box on top Power Cord Length 48 Communication Cable 48 Minimum Flow rate is 18 GPM Other Known Part #'s: 0603-421002, 0603-416001

more >>
BW SPA PARTS
$275.95 See It
RPS-2300-72 - Migatron RPS-2300 Controller with Remote Sensing Head, 8"-72" range, (2) Iso

RPS-2300-72 - Migatron RPS-2300 Controller with Remote Sensing Head, 8"-72" range, (2) Isolated Form C Relay OutputsSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducerAdjustable delay controls2 independent range adjustmentsLED indicatorsIsolated Form C relay outputsSmall electronic controllerThe RPS-2300 is a single transducer device with 2 independant range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. The transducer heads are made of Delrin with epoxy face for the 14" and 36" sensors and Valox with a silicon face for the 72". A sealed silicon rubber sensing face is used making this sensor best suited for environments where dirt is a problem. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves).With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor has a narrow sensing beam and operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. Download the RPS-2300-72 datasheet in *.pdf format RPS230072

more >>
Walker EMD
$641.00 See It
RPS-2300-14 - Migatron RPS-2300 Controller with Remote Sensing Head, 4"-14" range, (2) Iso

RPS-2300-14 - Migatron RPS-2300 Controller with Remote Sensing Head, 4"-14" range, (2) Isolated Form C Relay OutputsSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducerAdjustable delay controls2 independent range adjustmentsLED indicatorsIsolated Form C relay outputsSmall electronic controllerThe RPS-2300 is a single transducer device with 2 independant range control adjustments, LED indicators, and form C relay outputs. These make the sensor well suited for high and low level control, or other applications where two set points are needed. The transducer heads are made of Delrin with epoxy face for the 14" and 36" sensors and Valox with a silicon face for the 72". A sealed silicon rubber sensing face is used making this sensor best suited for environments where dirt is a problem. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves).With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each set point. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducer allows for mounting of the sensor head in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor has a narrow sensing beam and operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cable are included. Optional cable lengths are available. Download the RPS-2300-14 datasheet in *.pdf format RPS230014

more >>
Walker EMD
$585.00 See It
RPS-102-240 - Migatron RPS-102 Controller with Remote Sensing Head, 10"-240" range, 1 Isol

RPS-102-240 - Migatron RPS-102 Controller with Remote Sensing Head, 10"-240" range, 1 Isolated Form C Relay Output for each TransducerSpecifications:Various sensing rangesBroad sensing beamLow frequency - 38.5kHz2-way power operationSmall remote transducersAdjustable delay controls2 multiplexed transducersLED indicatorIsolated Form C relay outputSmall electronic controllerThe RPS-102 has 2 multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board.One sensor (master) would send a signal by means of the X OUT and GND terminals. These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located alongside the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent isolated form C relays furnish N.O. and N.C. outputs. This sensor, which operates at a frequency of 38.5kHz, has a broad sensing beam which allows for detection of an object at greater angles of tilt. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-102-240 datasheet in *.pdf format RPS102240

more >>
Walker EMD
$798.00 See It
WLToys WL V911 4 Channel 2.4GHz Mini Radio Single Propeller RC Hel ...

WL Toys "V911" 2.4 GHz 4-Channel Single Blade Helicopter 4-channel Remote Control with Trim and LCD Display 2.4 GHz Technology - Long Range and Interference-free Receptions Flight Stabilization System (Gyroscope Technology) Wind-resistant for Indoor and Outdoor Areas and Extreme - Flies in at a Wind Speed of 3-4 Very Agile and Nimble and Fast Response Times Very and but Thin Very Sturdy Aluminum Frame Construction Single Rotor Design for Realistic Flight Characteristics Dimensions: 22 Cm X 5 Cm X 8.2 Cm Weight: 27 G Battery: 3.7 120 MAh Lithium-Polymer Flight Time: 5-6 Minutes Range: 50 to 80 Meters Includes AC Adapter USB Charging Cable 2x Li-Po Battery and Instruction Manual Features: 4CH 2.4G RC Helicopter with Built-in Gyro. The First RC Helicopter That Can Fly Outdoor in Wind Weather (outdoor Wind Grade 3-4). Pioneering Single Propeller Design It Can Greatly Avoid the Resistence of Wind. High Quality Ultrathin Metal Canopy with Ultra Light Weight and Strong Resistance of Impact. High Tenacity Rotor Wing. Better Flying Performance Than ALIGN T-REX 100S: Extremely Steady and Extremely Agile. The Remote Control is Designed with a LCD Disply for Easier and More Precise Operation. Freely Flying Up Down Forward Backward Left to Fly Right to Fly Hover with Rapid Response. It is Suitable for Both Indoor and Outdoor Flying (the Wind Grade Should Be No More Than 4). 22cm Mini Helicopter. Specifications: Color: Orange Item No.: WLtoys V911 Battery for Helicopter: 3.7V 120mAh/15C Li-Polymer Flying Time: About 5-6 Minutes Charging Time: About 30 Mimutes (USB Charging) Controlling Distance: 50-80 Meters Battery for Controller: 6 * AA Batteries (Not Included) Helicopter Size: 22 * 5 * 8.2cm Helicopter Weight: 27g Remote Control Size: 18.5 * 14 * 7.6cm Remote Control Weight: 210g Package Includes: 1 * 2.4G 4CH RC Helicopter 1 * LCD Display Remote Control (Mode 2) 2 * Main Blade 1 * Lipo Charger 1 * USB Charging Cable 2 * Li-polymer Battery 1 * Bilingual User Manual Kindly Note That This Item Will Be Packed in Foam Box for a Safety Trip There No Original Box Thanks.

more >>
Fruugo
$64.49 See It
UDIRC U816 2.4G 4CH 4-Axis Mini RC UFO 360 Eversion Helicopter

Feature: 4 Motors Drivingstable Flying Ability Guarantee Free Flight for All Flying Actions Module Designationeasy Install and Repair. 4 AXES GYRO and Posture Control Intergrated Designation Guarantee the Precise Positioning. Over 7 Minutes Flying Time Specification: Model No. U816 Materials: ABS Weight: 30g Size:9.6x9.6cm Main Wing Size:5.5 CM Box Size:33.5x23.5x9cm Helicopter Battery: 3.7v 240mAh Rechargeable Li-Po Battery Charging Time: 60 Minutes Flight Duration: About 7-9 Minutes Transmitter Battery: 4 X AA Batteries(not Include) Remote Distance: Up to 30m Package Contents: 1 X U816 UFO (New Package) 1 X Transmitter 1 X USB Charging Cable 2 X 3.7v 250mah Batteries 1 X Charger 2 X Propeller A 2 X Propeller B 1 X Instruction Manual

more >>
Fruugo
$55.54 See It
RPS-302-72 - Migatron RPS-302 Controller with Remote Sensing Head, 8"-72" range, Isolated

RPS-302-72 - Migatron RPS-302 Controller with Remote Sensing Head, 8"-72" range, Isolated Form C Relay for each TransducerSpecifications:Various sensing rangesNarrow sensing beamHigh frequency2-way power operationSealed remote transducersAdjustable delay controls2 multiplexed transducersLED indicatorsIsolated Form C relay outputsSmall remote transducerThe RPS-302 has 2 sealed, multiplexed transducers with independent range control adjustments, LED indicators, and form C relay outputs. This sensor also has a unique master and slave feature which enables many of the same units to be used within close proximity of one another without cross-talk interference. For example, if three sensors are needed in a close area, one sensor would be left as a master and the other two would be slaves. This is done by means of the X IN, X OUT, and GND connection on the board. One sensor (master) would send a signal by means of the X OUT and GND terminals.These would be connected to the X IN and GND terminals of the other two sensors (slaves). With the sensors connected in this way, all units would be transmitting and receiving at the same time. This then would prevent cross-talk and enable all three sensors, or all six transducers, to be used at the same time in close proximity of one another. There are also separate turn ON and turn OFF DELAY potentiometers provided for each transducer. All four DELAY controls are located along side the black module inside the enclosure box. The remote transducers allow for mounting of the sensor heads in cramped spaces while the controller is out of the way. The (2) independent and isolated form C relays furnish N.O. and N.C. outputs. This sensor, operates at a frequency of 222kHz for the 14" and 36" ranges and 150kHz for the 72" range. This sensor has a narrow sensing beam. Mounting flanges, LED indicators, ranging potentiometers, and 6-ft. transducer cables are included. Optional cable lengths are available. Download the RPS-302-72 datasheet in *.pdf format RPS30272

more >>
Walker EMD
$971.00 See It
Samsung UN32H5500AF LED-LCD TV

LED-LCD TV - Color: Black Hairline - Green Compliant: Green Compliant - Ethernet Technology: Ethernet - Screen Size: 32" - Aspect Ratio: 16:9 - Green Compliance Certificate/Authority: ENERGY STAR - Wi-Fi: Wi-Fi

more >>
$329.99 - $397.99 Compare Prices at 2 stores
Search within results