No exact matches found for lee carbide reloading dies 9mm luger 9x21mm
59 similar items found
Case Length Gauge is a precise, easy way to trim to length and square the case mouth Used with the Cutter and Lock Stud Mfg: Lee
Easy-to-use, self-contained boresighting system fits in the chamber of your rifle or pistol and projects a powerful red laser beam aligned with the bore axis for sighting to the point-of-aim without firing a shot. Works with scopes, holographic red dot sights, and iron sights. Durable, machined brass housing looks like a cartridge case but actually contains the entire laser system and batteries. Insert the batteries and screw the cap on the housing to turn on the laser; remove the batteries to turn off. Insert the entire assembly into the chamber, gently close the action, and aim at a target 20-30 yards away. Adjust windage and elevation of the scope or sights so point-of-aim is zeroed on Mfg: Sightmark SPECS: Machined brass. Laser wavelength, 632-650 nm. Sighting range, 15-100 yards. Dot size, 2 at 100 yards. Includes (2) AG5 button cell batteries, nylon carrying case, and instructions. .223 Rem also fits .222 Rem, 5.56 x 45 NATO, 5.6 x 50, 6 x 47. 7mm Rem/.264 Win also fits 8mm Rem, .338 Win.
Convenient kits contain Go and No-Go gauges for accurately checking chamber length to make sure it meets SAAMI specs. These gauges are essential tools for ensuring a tight, accurate, safe chamber when chambering a new barrel. Always have a set on hand to check for correct headspace before buying or firing a new gun. Comes in a handy, durable plastic carrying case. Mfg: Clymer SPECS: Steel, precision machined to SAAMI specs. Each set contains one go gauge and one no-go gauge in a single caliber as listed below.
One of these durable, 4140 heat-treated carbon steel barrels is a critical component in converting an AR-15 into a fast-shooting, low-recoil carbine or pistol chambered in 9x19mm Luger. One-piece, fully machined barrel extension provides for reliable feeding/chambering. 1-14" twist 6-groove rifling is optimized for the 9x19mm round for optimal performance. Available in 16", 10.5", and 5.5" lengths. All NFA rules apply. Mfg: Yankee Hill Machine Co., Inc. SPECS: 4140 steel, heat-treated to Rc 25-32, matte black finish. .750" (1.9cm) O.D. at gas block. 1-14" twist rifling. ½"-36 muzzle threads.
Features: Sig Sauer factory P938 magazines Available with a 7 or 6 round capacity 9mm Luger Stainless steel body and follower 7rd magazine features an extended polymer basepad Mfg: Sig Sauer Fits Sig Sauer P938. 7 or 6 round, 9mm Luger capacity.
The finest phosphor bronze bristles on a looped and wound shank; in sizes to correctly fit the chambers of most popular rifle and handgun rounds on the market. Mfg: Brownells SPECS: 8-32 thread.
Set includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Shell Holder, Powder Dipper and Instructions/Load Data Carbide dies requires no sizing lube Mfg: Lee
Set includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Carbide Factory Crimp Die, Shell Holder, Powder Dipper and Instructions/Load Data Carbide Factory Crimp Die allows you to separate the bullet seating from the crimping operation - It makes setup much easier and the die has the added feature of a carbide resizer that does a finish sizing pass on the completed round 50 Beowolf contains a STEEL sizing die and STEEL taper crimp die NOT a factory crimp die. Mfg: Lee
You are bidding on a BRAND NEW -still in the box- Lee Carbide 3-Die Set 9mm Luger. LEE #90509. Set includes a Carbide Sizer Die, Powder Through Expander Die, Bullet Seater Die and a 2 year warranty. Reloading with carbide dies requires no sizing lube.Technical Information Material: Steel Accessories: Plastic Container Shellholder powder dipper load data sheet Notes: Adjustable crimp from slight taper to full roll Please check out my other LEE Melting/Casting/Reloading items by click on the blue
Sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability The adjusting screw quickly and easily sets the desired amount of crimp Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders Made of steel and features an internal carbide ring Carbide dies do not require the use of case lube Mfg: Lee
Universal shell holder used in most brands of reloading presses Will not work with Lee Auto Prime Mfg: Lee
This Luger Pin is approximately 1 inch in size.. This pin is usually shipped in 1-5 business days and as with all of our products carries a 100% customer satisfaction guarantee.
The very best abrasive compound for ''''hard fitting'''' two pieces of steel. Stands up to continued fitting even on hardened and heat-treated steel. Silicon carbide grit combined with a thick, long lasting lubricant breaks down into smaller and smaller sharp-edged particles to keep cutting longer than aluminum oxide compounds. For use on steel only. Remove with solvent. Mfg: Brownells SPECS: 4 fl. oz. (118 ml).
The Lee Aluminum 4-hole Turret is for quick caliber change for the 4-Hole Turret Press and Classic Turret Press. This 4 hole turret will not fit inside the Lee Pro 1000 or Lee 3 Hole Turret Press. Mfg: Lee
Grips the shell for a firm fit in the press during reloading or priming operations.
The TAPCO Masterpiece Defender 9MM Luger Magazine is molded with reinforced composite polymer to provide years of dependable service. Sturdy horizontal ridges provide increased gripping surface, making insertion and extraction of the magazine easier in wet or muddy conditions. The chrome silicon spring ensures flawless feeding. Black finish. Made in the USA. Holds 32 rounds.
This listing is for one 9mm luger bullets necklace. The length of this bullet is around 1 1/8"and it is made of brass, the necklace length is 24". It has had powder removed, so it can't be fired.Buy and enjoy! Shipping free within US only with delivery confirmation number.
Keeping a few extra factory magazines near you is never a bad idea. With the Ruger LC9 9MM Luger Magazine, you can save time and money at the range. Factory replacement parts are manufactured to the exact same specifications and tolerances. The same manufacturing materials as the original parts are used to design this magazine, guaranteeing excellent fit and reliable operation. Includes integrated grip extension on the end of the grip. Steel blue finish. Holds 9 rounds.
Whether for bullseye, action or cowboy shooting, pistol reloaders most often are looking to generate volumes of reloads which deliver consistent quality. That's why Lyman Pistol Dies are such a good choice and they fit virtually any reloading press, including the popular progressives. Most importantly, when it comes to precision, smoothness and versatility, Lyman Pistol Dies are unsurpassed. These dies deliver round after round of the high performance ammo serious shooters demand. 9mm Luger Carbide 3-die set.
Combines popular carbide 3-die set with factory crimp die. Packed in flat, 4-die box with air-tight hinged cover to keep precision machined dies in perfect condition.