1 to 20 of  100 products for power sequencer refurbished ac 230v universal 3001290 sun micro

No exact matches found for power sequencer refurbished ac 230v universal 3001290 sun micro

100 similar items found

Bison Variable Frequency AC Chassis Drive 230V # 170-503-0002

Input 230V Single Phase, Output 230V 3-phase; MAX Output Current AMPS 2.4; Output Frequency 0-120 Hz; Compact Size: 4.3" x 3.7" with industry standard mounting hole pattern.; Easy to Calibrate and Set-up, On board trimmer pot adjustments; Torque "Foldback" Feature; The cost-conscious and compact chassis design of Bison VFD Chassis Drives maintain the industry standard for mounting hole location and the coded LEDs make it easy to visually determine the drive status. With it's compact design and application flexibility, this is an excellent choice for most AC applications. Easy to Calibrate and Set-up: On board trimmer pot adjustments for boost, maximum speed, acceleration, and deceleration. Torque "Foldback" Feature: Allows up to 200% torque for short periods to overcome intermittent peak loads, then reduces the torque to a preset safe level. Switching Frequency: 16 kHz switching frequency, with option to change between 4 and 16 kHz in the field. A high switching frequency results in quiet motor operation. Adjustments to a lower frequency if desired can be done in the field.

more >>
Electric Motor Warehouse
$247.78 See It
Single Phase to Three Phase Inverter 5.5 amp 230V # KBVF-26D

MAX 5.5 Output amps @ 230 Volt. Operates standard 208/230V 3-phase AC motors, with 230Vÿinput single phase Power. Start provides more than 200% starting torque. Speed potentionmeter (pot) provided. Jumper selections: Forward-stop-reverse/Enable-automatic-manual. Not Recommended for use on air compressors. Speed potentiometer must be connected or the motor will not spin, without the pot the speed is set at zero and you will burn the motor up. "KBVF" Frequency Drive. A Low Cost, full featured, Motor Control / Frequency Drive. with 100% power output. Single phase input - Three phase output. If you have been to a used equipment auction and purchased a mill, lathe, drill press or other piece machinery with a three phase motor and are looking for a low cost solution to power it with single phase power. This may be your low cost solution. Unlike some of the electronic phase inverters that only output 2/3 of the power, this unit puts out 100% 3 phase power with 200% starting torque. You will need to eliminate any other motor switches. You will connect the motor directly to the 3 terminals on the converter. Otherwise the contacts from the old motor starter will allow feedback to the control that will damage the unit. The KB control becomes the motor starter. The unit should be powered through an electric power disconnect. When selecting drive size the motor amps cannot exceed the rated output amps of the control. Standard Features: Operates standard 208/230 VAC 3-phase AC motors, with 230 VAC input single phase. Power Start provides more than 200% starting torque. 30:1 speed range with full motor torque (Speed potentionmeter (pot) provided). (Motor should be inverter rated if using speed control feature). Controls 50hz and 60hz motors with a convenient jumper selection. Sinewave coded PWM-provides high motor torque and efficient operation. 16 khz switching frequency-provides quite motor operations. Motor overload protection. Jumper selections: Forward-stop-reverse/Enable-automatic-manual. You can use a 3-position toggle switch. Start 0-60,0-120, 0-50hz.Trimpot adjustments: Minimum Speed-min, Maximum Speed-Max. Important Application Information: Most fan-cooled (TEFC) 3-phase motors will overheat. if used with an inverter beyond a limited speed range at full rated torque. Therefore, it is necessary to reduce motor load as speed is decreased.Attention: Your motor amps cannot exceed the rated output amps of the converter. Note: Motor can not be run through contacts. Motor to be wired directly to controller. You will need to soldier leads to the potentiometer and connect it to the control.

more >>
Electric Motor Warehouse
$230.34 See It
Single Phase to Three Phase Inverter 1 hp 230V # KBVF-24D

1 HP; MAX 4 Output amps @ 230 Volt. Operates standard 208/230V 3-phase AC motors, with 230Vÿinput single phase Power. Start provides more than 200% starting torque. Speed potentionmeter (pot) provided. Jumper selections: Forward-stop-reverse/Enable-automatic-manual. Not Recommended for use on air compressors. Speed potentiometer must be connected or the motor will not spin, without the pot the speed is set at zero and you will burn the motor up. "KBVF" Frequency Drive. A Low Cost, full featured, Motor Control / Frequency Drive. with 100% power output. Single phase input - Three phase output. If you have been to a used equipment auction and purchased a mill, lathe, drill press or other piece machinery with a three phase motor and are looking for a low cost solution to power it with single phase power. This may be your low cost solution. Unlike some of the electronic phase inverters that only output 2/3 of the power, this unit puts out 100% 3 phase power with 200% starting torque. You will need to eliminate any other motor switches. You will connect the motor directly to the 3 terminals on the converter. Otherwise the contacts from the old motor starter will allow feedback to the control that will damage the unit. The KB control becomes the motor starter. The unit should be powered through an electric power disconnect. When selecting drive size the motor amps cannot exceed the rated output amps of the control. Standard Features: Operates standard 208/230 VAC 3-phase AC motors, with 230 VAC input single phase. Power Start provides more than 200% starting torque. 30:1 speed range with full motor torque (Speed potentionmeter (pot) provided). (Motor should be inverter rated if using speed control feature). Controls 50hz and 60hz motors with a convenient jumper selection. Sinewave coded PWM-provides high motor torque and efficient operation. 16 khz switching frequency-provides quite motor operations. Motor overload protection. Jumper selections: Forward-stop-reverse/Enable-automatic-manual. You can use a 3-position toggle switch. Start 0-60,0-120, 0-50hz.Trimpot adjustments: Minimum Speed-min, Maximum Speed-Max. Important Application Information: Most fan-cooled (TEFC) 3-phase motors will overheat. if used with an inverter beyond a limited speed range at full rated torque. Therefore, it is necessary to reduce motor load as speed is decreased.Attention: Your motor amps cannot exceed the rated output amps of the converter. Note: Motor can not be run through contacts. Motor to be wired directly to controller. You will need to soldier leads to the potentiometer and connect it to the control.

more >>
Electric Motor Warehouse
$183.75 See It
Single Phase to Three Phase Inverter 1/2 hp 230V # KBVF-23D

1/2 HP; MAX 2.4 Output amps @ 230 Volt. Operates standard 208/230V 3-phase AC motors, with 230Vÿinput single phase Power. Start provides more than 200% starting torque. Speed potentionmeter (pot) provided. Jumper selections: Forward-stop-reverse/Enable-automatic-manual. Not Recommended for use on air compressors. Speed potentiometer must be connected or the motor will not spin, without the pot the speed is set at zero and you will burn the motor up. "KBVF" Frequency Drive. A Low Cost, full featured, Motor Control / Frequency Drive. with 100% power output. Single phase input - Three phase output. If you have been to a used equipment auction and purchased a mill, lathe, drill press or other piece machinery with a three phase motor and are looking for a low cost solution to power it with single phase power. This may be your low cost solution. Unlike some of the electronic phase inverters that only output 2/3 of the power, this unit puts out 100% 3 phase power with 200% starting torque. You will need to eliminate any other motor switches. You will connect the motor directly to the 3 terminals on the converter. Otherwise the contacts from the old motor starter will allow feedback to the control that will damage the unit. The KB control becomes the motor starter. The unit should be powered through an electric power disconnect. When selecting drive size the motor amps cannot exceed the rated output amps of the control. Standard Features: Operates standard 208/230 VAC 3-phase AC motors, with 230 VAC input single phase. Power Start provides more than 200% starting torque. 30:1 speed range with full motor torque (Speed potentionmeter (pot) provided). (Motor should be inverter rated if using speed control feature). Controls 50hz and 60hz motors with a convenient jumper selection. Sinewave coded PWM-provides high motor torque and efficient operation. 16 khz switching frequency-provides quite motor operations. Motor overload protection. Jumper selections: Forward-stop-reverse/Enable-automatic-manual. You can use a 3-position toggle switch. Start 0-60,0-120, 0-50hz.Trimpot adjustments: Minimum Speed-min, Maximum Speed-Max. Important Application Information: Most fan-cooled (TEFC) 3-phase motors will overheat. if used with an inverter beyond a limited speed range at full rated torque. Therefore, it is necessary to reduce motor load as speed is decreased.Attention: Your motor amps cannot exceed the rated output amps of the converter. Note: Motor can not be run through contacts. Motor to be wired directly to controller. You will need to soldier leads to the potentiometer and connect it to the control.

more >>
Electric Motor Warehouse
$152.25 See It
DAIKIN GOODMAN Commercial AC Split System 4 Ton 208-230V 3 phase with Air Handler

Package Includes: DX13SA0483 Air Conditioner and ARUF48D14 Air Handler. AC Model Number: DX13SA0483 Air Handler Model Number: ARUF48D14 DAIKIN GOODMAN Commercial AC Split System 4 Ton 208-230V 3 phase with Air Handler DX13S Commercial Air ...

more >>
Ingram's Water and Air
$2,304.00 See It
DAIKIN GOODMAN Commercial AC Split System 5 Ton 208-230V 3 phase with Air Handler

Package Includes: DX13SA0603 Air Conditioner and ARUF60D14 Air Handler. AC Model Number: DX13SA0603 Air Handler Model Number: ARUF60D14 DAIKIN GOODMAN Commercial AC Split System 5 Ton 208-230V 3 phase with Air Handler DX13S Commercial Air ...

more >>
Ingram's Water and Air
$2,449.00 See It
DAIKIN GOODMAN Commercial AC Split System 3 Ton 208-230V 3 phase with Air Handler

Package Includes: DX13SA0363 Air Conditioner and ARUF36C14 Air Handler. AC Model Number: DX13SA0363 Air Handler Model Number: ARUF36C14 DAIKIN GOODMAN Commercial AC Split System 3 Ton 208-230V 3 phase with Air Handler DX13S Commercial Air ...

more >>
Ingram's Water and Air
$1,989.00 See It
DAIKIN GOODMAN Commercial AC Condenser 10 Ton 208-230V 3 phase with Air Handler

Package Includes: DX11SA1203 Air Conditioner and DAR1204 Air Handler. AC Model Number: DX11SA1203 Air Handler Model Number: DAR1204 DAIKIN GOODMAN Commercial AC Condenser 10 Ton 208-230V 3 phase with Air Handler DX11S Commercial Air Conditioner The ...

more >>
Ingram's Water and Air
$4,969.00 See It
DAIKIN GOODMAN Commercial AC Condenser 7.5 Ton 208-230V 3 phase with Air Handler

Package Includes: DX11SA0903 Air Conditioner and DAR0904 Air Handler. AC Model Number: DX11SA0903 Air Handler Model Number: DAR0904 DAIKIN GOODMAN Commercial AC Condenser 7.5 Ton 208-230V 3 phase with Air Handler DX11S Commercial Air Conditioner ...

more >>
Ingram's Water and Air
$4,641.00 See It
COOLLINE A903 Oil Cooler, AC, 20200 GPM, 230/460 V, 3 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 20 to 200 GPM, Voltage 230/460, Motor Amps 8.6/4.3, 3 Motor HP, Port Size 2 In SAE 4 Bolt Flange, HP Heat Removed 90, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 30.19 In, Width 37.01 In,...

more >>
Zoro
$3,353.08 See It
COOLLINE A553 Oil Cooler, AC, 880 GPM, 230/460 V, 2 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 8 to 80 GPM, Voltage 230/460, Motor Amps 6.2/3.1, 2 Motor HP, Port Size SAE #20, HP Heat Removed 55, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 25.89 In, Width 30.31 In, Depth 19.5 In,...

more >>
Zoro
$1,987.40 See It
DAIKIN GOODMAN Commercial Heat Pump Condenser 7.5 Ton 208-230V 3 phase with Air Handler

Package Includes: DZ11SA0903 Air Conditioner and DAR0904 Air Handler. AC Model Number: DZ11SA0903 Air Handler Model Number: DAR0904 DAIKIN GOODMAN Commercial AC Condenser 7.5 Ton 208-230V 3 phase with Air Handler DZ11S Commercial Air Conditioner ...

more >>
Ingram's Water and Air
$5,234.00 See It
COOLLINE A151 Oil Cooler, AC, 880 GPM, 115/230 V, 1/2 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 8 to 80 GPM, Voltage 115/230, Motor Amps 7/3.5, 1/2 Motor HP, Port Size SAE #16, HP Heat Removed 15, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 15.91 In, Width 16.54 In, Depth 16 In,...

more >>
Zoro
$844.24 See It
DAIKIN GOODMAN Commercial Heat Pump Condenser 4 Ton 208-230V 3 phase with Air Handler

Package Includes: DZ13SA0483 Air Conditioner and ARUF48D14 Air Handler. AC Model Number: DZ13SA0483 Air Handler Model Number: ARUF48D14 DAIKIN GOODMAN Commercial Heat Pump Condenser 4 Ton 208-230V 3 phase with Air Handler DZ13S Commercial Air ...

more >>
Ingram's Water and Air
$2,622.00 See It
COOLLINE A201 Oil Cooler, AC, 450 GPM, 115/230 V, 1/2 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 4 to 50 GPM, Voltage 115/230, Motor Amps 8/4, 1/2 Motor HP, Port Size SAE #20, HP Heat Removed 20, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 19.6 In, Width 21.65 In, Depth 15.5 In,...

more >>
Zoro
$936.99 See It
DAIKIN GOODMAN Commercial Heat Pump Condenser 3 Ton 208-230V 3 phase with Air Handler

Package Includes: DZ13SA0363 Air Conditioner and ARUF36C14 Air Handler. AC Model Number: DZ13SA0363 Air Handler Model Number: ARUF36C14 DAIKIN GOODMAN Commercial Heat Pump Condenser 3 Ton 208-230V 3 phase with Air Handler DZ13S Commercial Air ...

more >>
Ingram's Water and Air
$2,284.00 See It
COOLLINE AL51 Oil Cooler, AC, 230 GPM, 115/230 V, 1/4 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 2 to 30 GPM, Voltage 115/230, Motor Amps 5.4/2.7, 1/4 Motor HP, Port Size SAE #12, HP Heat Removed 5, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 13.74 In, Width 13.78 In, Depth 12.56 In,...

more >>
Zoro
$723.95 See It
DAIKIN GOODMAN Commercial Heat Pump Condenser 5 Ton 208-230V 3 phase with Air Handler

Package Includes: DZ13SA0603 Air Conditioner and ARUF60D14 Air Handler. AC Model Number: DZ13SA0603 Air Handler Model Number: ARUF60D14 DAIKIN GOODMAN Commercial Heat Pump Condenser 5 Ton 208-230V 3 phase with Air Handler DZ13S Commercial Air ...

more >>
Ingram's Water and Air
$2,876.00 See It
COOLLINE A101 Oil Cooler, AC, 450 GPM, 115/230 V, 1/2 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 4 to 50 GPM, Voltage 115/230, Motor Amps 7/3.5, 1/2 Motor HP, Port Size SAE #16, HP Heat Removed 10, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 15.91 In, Width 15.75 In, Depth 14.5 In,...

more >>
Zoro
$790.19 See It
COOLLINE A81 Oil Cooler, AC, 230 GPM, 115/230 V, 1/3 HP

$50+ Orders Ship Free

Forced Air Oil Cooler, AC Motor, Flow Ranges 2 to 30 GPM, Voltage 115/230, Motor Amps 5.6/2.8, 1/3 Motor HP, Port Size SAE #12, HP Heat Removed 8, NEMA/IEC Frame 56C, Max Pressure 377 PSI, Max Temp 250, Aluminum Construction, Black Painted Finish, Height 14.25 In, Width 13.78 In, Depth 13.27 In,...

more >>
Zoro
$688.94 See It
Search within results
  • Find by Price
    • $ to $