1 to 20 of  20 products for shotgun 11 87

Result for "shotgun 11 87"
Shotgun Modular Extension Tubes - Rem 870/1100/11-87 Mxt Tube +2

Based off of the standard Nordic Extension Tube, the Modular eXtension Tube incorporates new features designed to eliminate common problems with shotgun magazine extensions.  The MXT features a reinforced magazine tube end-cap, which prevents end-cap damage from high recoil and impact.  A new clamp relief groove eliminates clamp slip during recoil, which can damage the finish of the firearm and change the point of impact.  MXTs feature the same threads on either end of the tube, allowing the user to flip it, changing the location of the clamp groove.  Includes spring. Available for the following models: Benelli M1/M2, Super Black Eagle I & II Bene Mfg: Nordic Components Aluminum construction, matte black finish.  Available for: Benelli M1/M2, Super Black Eagle I & II, Benelli Nova/Super Nova, Beretta Xtrema/Xtrema2/Tx4/A400, CZ 712, Remington 870/1100/11-87/105 CTi, Winchester SX2/SX3, Browning Gold/Silver, FN SLP, Mossberg 590, 930, 935.  Tube

more >>
Brownells
$75.99 See It
Shotgun Magazine Extension - 12 Ga Blue Mag Ext, 3-Rds Fit Rem. 870/1100/11-87*

Gives you additional magazine capacity in only a minute. Quick and simple to install and remove. Threaded tube replaces magazine cap screw. Perfect for Shotgun Action Shooting events or Law Enforcement. Sling Swivel Clamp (included on Remington models only) secures extension to the barrel for extra support. Provides a convenient front mounting point for carry strap or sling. Sling Swivel Clamp also available separately. Mfg: Choate SPECS: Extension - Steel, blued or parkerized, matte finish. 12 ga. only. Includes extended spring, follower and swivel clamp. Sling Swivel Clamp - Blued or parkerized steel, front and rear 1" swivel rings with studs. Chart indicates number of ROUNDS (RDS) in addition to factory magazine capaci

more >>
Brownells
$44.99 See It
Shotgun Magazine Extension - 12 Ga Blue Mag Ext, 5-Rds Fit Rem. 870/1100/11-87*

Gives you additional magazine capacity in only a minute. Quick and simple to install and remove. Threaded tube replaces magazine cap screw. Perfect for Shotgun Action Shooting events or Law Enforcement. Sling Swivel Clamp (included on Remington models only) secures extension to the barrel for extra support. Provides a convenient front mounting point for carry strap or sling. Sling Swivel Clamp also available separately. Mfg: Choate SPECS: Extension - Steel, blued or parkerized, matte finish. 12 ga. only. Includes extended spring, follower and swivel clamp. Sling Swivel Clamp - Blued or parkerized steel, front and rear 1" swivel rings with studs. Chart indicates number of ROUNDS (RDS) in addition to factory magazine capaci

more >>
Brownells
$49.99 See It
Shotgun Magazine Extension - 12 Ga Parkerized Mag Ext, 2-Rds Fit Rem. 870/1100/11-87*

Gives you additional magazine capacity in only a minute. Quick and simple to install and remove. Threaded tube replaces magazine cap screw. Perfect for Shotgun Action Shooting events or Law Enforcement. Sling Swivel Clamp (included on Remington models only) secures extension to the barrel for extra support. Provides a convenient front mounting point for carry strap or sling. Sling Swivel Clamp also available separately. Mfg: Choate SPECS: Extension - Steel, blued or parkerized, matte finish. 12 ga. only. Includes extended spring, follower and swivel clamp. Sling Swivel Clamp - Blued or parkerized steel, front and rear 1" swivel rings with studs. Chart indicates number of ROUNDS (RDS) in addition to factory magazine capaci

more >>
Brownells
$44.99 See It
Shotgun Magazine Extension - 12 Ga Blue Mag Ext, 2-Rds Fit Rem. 870/1100/11-87*

Gives you additional magazine capacity in only a minute. Quick and simple to install and remove. Threaded tube replaces magazine cap screw. Perfect for Shotgun Action Shooting events or Law Enforcement. Sling Swivel Clamp (included on Remington models only) secures extension to the barrel for extra support. Provides a convenient front mounting point for carry strap or sling. Sling Swivel Clamp also available separately. Mfg: Choate SPECS: Extension - Steel, blued or parkerized, matte finish. 12 ga. only. Includes extended spring, follower and swivel clamp. Sling Swivel Clamp - Blued or parkerized steel, front and rear 1" swivel rings with studs. Chart indicates number of ROUNDS (RDS) in addition to factory magazine capaci

more >>
Brownells
$44.99 See It
Shotgun Magazine Tube Cap With Swivel Base - Rem Magazine Cap W/Swivel Base

Machined steel magazine cap with built-in, 360° rotating swivel stud makes it easy to convert your Remington shotgun to accept a carry sling. Unique cap design includes both ratchet and ball/spring type detent systems for no-hassle installation. Includes a ¾" long, wood screw swivel stud for the buttstock. Sling loops not included. Installation requires drilling of buttstock. Mfg: Outdoor Connection SPECS: Steel, black, matte finish. Includes magazine cap with swivel stud, wood screw stud w/black spacer, and instructions. Models available for Remington 870/1100/11-87/11-96, 12 ga. only and Mossberg 500 and Maverick 88, 20 ga. & 12 ga. Moss/Mav includes spanner wrench.

more >>
Brownells
$16.99 See It
Remington 1100/11-87 Piston/Seal Field Service Kit - 1100 Piston Field Service Kit

Don’t get caught short or let a broken shotgun ruin your hunt. Convenient, pre-packaged kits contain the parts most often required for emergency, field repairs. All parts are Remington, Mossberg and Winchester Factory, tagged with the Brownells stock number, and current factory parts number. Two barrel seals, one piston and one piston seal. Fits all 12 ga., plus large-frame 16/20 ga. guns with X or N in serial number. Mfg: Brownells SPECS: Kits contain one each of parts listed unless noted.

more >>
Brownells
$32.99 See It
Extended Magazine Tube - 2 Round, Loop Left-Side

Machined steel magazine extensions increase capacity without gunsmithing or permanent alterations to your Remington 870, 1100 or 11-87 shotgun. Knurled, threaded collar screws onto the end of the mag tube. Includes high-performance, extended length magazine spring and an unbreakable, high-visibility, nylon follower. Loop models features a stationary loop on either the bottom or left side of the extension to accept direct attachment of tactical-style slings without swivels. QD stud models include a quick-detach, swivel stud mounted either in the center of the magazine cap or at the front of a plate below the extension to accept slings with quick-detach swivels. All model Mfg: Scattergun Technology SPECS: Steel, gray parkerized finish. Fits Remington 870/1100/11-87, 12 ga. only. 1-Shot - 2'''' (5cm) long, 2-Shot - 6'''' (15.2cm) long.

more >>
Brownells
$44.99 See It
Service Kit For Remington 870, 1100 & 11-87 - 870 Service Kit-Complete W/Tool Box

With the help of the fine folks at Remington, the armorer and gunsmith can now have a kit with tools we have adapted from ­factory designs for repairing and maintaining what has probably become the world's most popular pump shotgun—the Remington 870. Special thanks has to go to the entire Remington organization for recognizing the importance of proper tools to the gunsmith. This tool kit makes it easier for the ­armorer or gunsmith to repair the 870 at the bench or in the field. Even though some of the tools may seem like overkill, keep in mind that the designs are based on the factory's years of experience and are intended to stand up to constant use. Whether you're a ­dep Mfg: Brownells

more >>
Brownells
$349.99 See It
Service Kit For Remington 870, 1100 & 11-87 - 870 Service Kit-Tools Only (No Box)

With the help of the fine folks at Remington, the armorer and gunsmith can now have a kit with tools we have adapted from ­factory designs for repairing and maintaining what has probably become the world's most popular pump shotgun—the Remington 870. Special thanks has to go to the entire Remington organization for recognizing the importance of proper tools to the gunsmith. This tool kit makes it easier for the ­armorer or gunsmith to repair the 870 at the bench or in the field. Even though some of the tools may seem like overkill, keep in mind that the designs are based on the factory's years of experience and are intended to stand up to constant use. Whether you're a ­dep Mfg: Brownells

more >>
Brownells
$363.99 See It
Shotgun Anti-Walk Trigger Housing Pin - Remington Trigger Pins

Eliminates pin drift in the receiver holes so your trigger housing stays in the same place for every shot. Slotted, truss head screws at each end of pin keeps trigger housing properly aligned and free of wobble. Helps deliver reliable trigger performance in tactical and competition guns. Remington includes both front and rear, anti-walk trigger pins. Mfg: Brownells SPECS: Steel, blued finish. Remington - Fits Remington 870/1100/11-87. Mossberg - Fits Mossberg 500/590. Winchester - Fits Winchester 1200/1300/1400. Benelli - Fits Benelli Super 90, Winchester Super X and Browning Gold.

more >>
Brownells
$15.99 See It
Extended Magazine Tube - 2 Round, Od Stud, Front

Machined steel magazine extensions increase capacity without gunsmithing or permanent alterations to your Remington 870, 1100 or 11-87 shotgun. Knurled, threaded collar screws onto the end of the mag tube. Includes high-performance, extended length magazine spring and an unbreakable, high-visibility, nylon follower. Loop models features a stationary loop on either the bottom or left side of the extension to accept direct attachment of tactical-style slings without swivels. QD stud models include a quick-detach, swivel stud mounted either in the center of the magazine cap or at the front of a plate below the extension to accept slings with quick-detach swivels. All model Mfg: Scattergun Technology SPECS: Steel, gray parkerized finish. Fits Remington 870/1100/11-87, 12 ga. only. 1-Shot - 2'''' (5cm) long, 2-Shot - 6'''' (15.2cm) long.

more >>
Brownells
$44.99 See It
Shotgun Magazine Tube Extension - 2-Shot Rem Magazine Tube Extension

Short, screw-on magazine extensions add one or two additional rounds to tactical and sporting shotguns without increasing overall gun length. Replaces factory magazine cap with no permanent modifications. Machined from solid steel bar stock for a much stronger system to resist dents. Included sling loop can be installed for left- or right-handed shooters. Includes a smooth feeding stainless steel follower for enhanced reliability. Models available for Remington 870/1100/11-87 and Mossberg 590A1 shotguns. Mfg: Vang Comp Systems SPECS: Steel, black matte finish. Includes extension tube, follower, and extended magazine spring. Accepts 1¼” slings. 12 ga. only. 1-Shot – 2¼” (5.9cm) long. Models for Remington 870/1100/11-87 and Mossberg 590A1. 2-Shot – 6-3/16" (15.7) long. Fit

more >>
Brownells
$74.99 See It
Shotgun Sling Mount - Rem Right Hand Rear Mount

Designed for tactical operations, these mounts place the rear sling attachment point in front of the operator, so you can quickly shoulder your weapon without getting tangled. Allows single point sling attachment, or use with a front sling mount for two-point sling installation. Loop accepts slings up to 1¼" wide. Rear Mount installs directly behind receiver, in front of buttstock. Precision machined from aluminum billet, then hardcoat anodized matte black. Right hand model for Remington 870, 1100, and 11-87 positions sling on left side of stock. Ambi model for Remington 870, 1100, and 11-87 accepts HK-style clasps and other clip-on sling fasteners. Benelli version fits M1, M3 Mfg: Gg&G, Inc. SPECS: Rem Rear Mount - Aluminum, matte black. ¼" (6.4mm) long, 113/16" (4.6cm) wide, 17/8" (4.8cm) high. Fits 870/1100/11-87, Right Hand only. Rem Ambi Rear Mount - Aluminum, matte black. ¼" long, 2¼" (5.7cm) wide, 17/8" high.

more >>
Brownells
$26.99 See It
Shotgun Sling Mount - Rem Ambi Rear Mount

Designed for tactical operations, these mounts place the rear sling attachment point in front of the operator, so you can quickly shoulder your weapon without getting tangled. Allows single point sling attachment, or use with a front sling mount for two-point sling installation. Loop accepts slings up to 1¼" wide. Rear Mount installs directly behind receiver, in front of buttstock. Precision machined from aluminum billet, then hardcoat anodized matte black. Right hand model for Remington 870, 1100, and 11-87 positions sling on left side of stock. Ambi model for Remington 870, 1100, and 11-87 accepts HK-style clasps and other clip-on sling fasteners. Benelli version fits M1, M3 Mfg: Gg&G, Inc. SPECS: Rem Rear Mount - Aluminum, matte black. ¼" (6.4mm) long, 113/16" (4.6cm) wide, 17/8" (4.8cm) high. Fits 870/1100/11-87, Right Hand only. Rem Ambi Rear Mount - Aluminum, matte black. ¼" long, 2¼" (5.7cm) wide, 17/8" high.

more >>
Brownells
$26.99 See It
Shotgun Anti-Walk Trigger Housing Pin - Mossberg Trigger Pin

Eliminates pin drift in the receiver holes so your trigger housing stays in the same place for every shot. Slotted, truss head screws at each end of pin keeps trigger housing properly aligned and free of wobble. Helps deliver reliable trigger performance in tactical and competition guns. Remington includes both front and rear, anti-walk trigger pins. Mfg: Brownells SPECS: Steel, blued finish. Remington - Fits Remington 870/1100/11-87. Mossberg - Fits Mossberg 500/590. Winchester - Fits Winchester 1200/1300/1400. Benelli - Fits Benelli Super 90, Winchester Super X and Browning Gold.

more >>
Brownells
$7.99 See It
Shotgun Front Sights - Bd1007-G Spark Ii Sight, Green

RM2006 - ETA front sight for Remington Shotguns. Interchangeable green LitePipes: 2 round & 1 triangular with carrying case. Fits all ribbed 870, 1100 & 11-87 Remington Shotguns. BD1007-G - Threaded front bead replacement. Spark II sight, Green. Packaged with 5 threaded studs (6/48, 3/56, 5/40, 3mm x .5 & 3mm x .6) to fit all common shotguns with removable front bead. MB2003-G - Replaces Mid-Bead on target shotguns. Green. Standard press-fit tapered shank. MB2003-R - Replaces Mid-Bead on target shotguns. Red. Standard press-fit tapered shank. KR2005 - Steel base, 8 interchangeable litepipes, revolving carrying case, key, two 3-56 screws. Fits K-80 model Mfg: Hiviz

more >>
Brownells
$10.99 See It
Shotgun Speed Bolt Handle - Speed Bolt Handle, Winchester/Fn

Easy to install, oversized charging handle helps you clear misfeeds and eject a chambered round quickly and efficiently. Machined steel construction, with a distinctive tubular shape, and deep, corkscrewpattern flutes give an excellent purchase and stylish look. No gunsmithing required. Mfg: Nordic Components SPECS: Steel, matte black finish. Benelli/Beretta fits Benelli M1/M2 (12/20 gauge) and Beretta Extrema. Rem. fits Remington 12 gauge 1100 and 11-87. Win./FN fits Winchester SX2/SX3, FN SLP, and Browning Silver.

more >>
Brownells
$29.95 See It
Shotgun Speed Bolt Handle - Speed Bolt Handle, Benelli/Beretta

Easy to install, oversized charging handle helps you clear misfeeds and eject a chambered round quickly and efficiently. Machined steel construction, with a distinctive tubular shape, and deep, corkscrewpattern flutes give an excellent purchase and stylish look. No gunsmithing required. Mfg: Nordic Components SPECS: Steel, matte black finish. Benelli/Beretta fits Benelli M1/M2 (12/20 gauge) and Beretta Extrema. Rem. fits Remington 12 gauge 1100 and 11-87. Win./FN fits Winchester SX2/SX3, FN SLP, and Browning Silver.

more >>
Brownells
$24.99 See It
Extended Magazine Tube - 1 Round, Loop Left-Side

Machined steel magazine extensions increase capacity without gunsmithing or permanent alterations to your Remington 870, 1100 or 11-87 shotgun. Knurled, threaded collar screws onto the end of the mag tube. Includes high-performance, extended length magazine spring and an unbreakable, high-visibility, nylon follower. Loop models features a stationary loop on either the bottom or left side of the extension to accept direct attachment of tactical-style slings without swivels. QD stud models include a quick-detach, swivel stud mounted either in the center of the magazine cap or at the front of a plate below the extension to accept slings with quick-detach swivels. All model Mfg: Scattergun Technology SPECS: Steel, gray parkerized finish. Fits Remington 870/1100/11-87, 12 ga. only. 1-Shot - 2'''' (5cm) long, 2-Shot - 6'''' (15.2cm) long.

more >>
Brownells
$44.99 See It
Search within results