1 to 20 of  100 products for sinclair ar 15 ar 10 vise blocks sinclair ar 10 vise block

No exact matches found for sinclair ar 15 ar 10 vise blocks sinclair ar 10 vise block

100 similar items found

Sinclair Ar-15/And Ar-10 Lug Recess Tool - Sinclair Ar-15 Lug Recess Tool With Rolls

This one of a kind tool is used to clean the lug recess area on the AR-15 and AR-10 rifles. The lug recess area collects a lot of grease and debris and needs to be cleaned regularly. This tool compresses a cotton roll and then releases it so you can rotate it inside the lug recess area. Should be used wet with solvent, then followed up with a dry roll. One bag of cotton rolls, about 50, is included with each tool. Mfg: Sinclair International

more >>
Brownells
$29.99 See It
M16 & Ar-15 Chamber Brushes - Ar-10 Chamber Brush

Original military design, M16, with 8-36 thread for direct threading into the ''''Cleaning Rod, Small Arms'''', or AR-15 with 8-32 thread to fit standard rods. AR-10 cleans the larger .308 chamber used on these rifles. Bronze bristles fit chamber, longer, stainless steel tufts clean locking lug recesses. Mfg: Brownells SPECS: M16 - NSN 1005-00-999-1435, has 8-36 military thread. Meets Mil Spec: MIL-B-20100C. AR-15 and AR-10 have 8-32 standard thread. M16 and AR-15 are 37/8'''' (9.8cm) overall. AR-10, 4 3/8'''' (11.2cm).

more >>
Brownells
$5.99 See It
Ar-15/M16 Rear Tensioning Pin - Ar-15 Tensioning Pin

Takes out the play between upper and lower AR-15 receivers: provides a rock-solid lockup for more consistent accuracy and improved trigger pull. Thread-adjustable, all stainless steel pin installs quickly, replaces the push pin and will not alter or enlarge existing hole dimensions. Mfg: J P Enterprises SPECS: Stainless steel. AR-15 - .250" (6.3mm) nominal diameter. Fits receivers with .250" diameter receiver takedown pin holes. AR-10/SR-25 - Pin diameter .274" to .276" on pin ends.

more >>
Brownells
$37.99 See It
Sinclair Specialty Cleaning Rod Guides - Sinclair Ar-15 Rod Guide, 223 Rem

We make specialty rod guides for the AR family of rifles (AR-15, AR-10/SR25, and HK-91) and the Ruger 77/22 Hornet. The AR family rod guides are the O-ring style, while the Ruger 77/22 Hornet is one of our rimfire type rod guides. Includes new intergral solvent port. Mfg: Sinclair International

more >>
Brownells
$19.99 See It
Ar-15 Bullet Button - Lock Ar-15 Bullet-Button

Drop-in replacement for factory magazine release button retains the magazine in the lower receiver to conform with California Code of Regulations 978.20(a). Prevents rapid magazine removal, so your gun can meet the requirement for a permanent, non-detachable magazine. Installs in minutes. Magazine capacity can be no more than 10 rounds. Laws and regulations can change at any time; the user is responsible for making sure his rifle stays compliant. Mfg: Assault Planet SPECS: 7075 T6 aluminum, hardcoat anodized, black. Screws - carbon steel, black. Fits AR-15 and clones, Sig 556, and AR-style .308 rifles including ArmaLite® AR-10®, Bushmaster, Hess, Iron Cross, and J.D. Machine. Includes mounting hardware and instructions.

more >>
Brownells
$18.99 See It
Ar-10® 308/7.62 Magazines - Ar-10 Magazine, 25-Rd

Brand-new, factory-made, Generation II magazines built by ArmaLite® feature a spot-welded, heavy gauge steel body that won’t distort when fully loaded and a contoured follower designed to ensure exceptionally smooth, reliable feeding. These aren’t converted M14 magazines, but mags purpose-built specifically for the AR-10 Type "B" lowers only - the same mags that come with new rifles. Available in 5-, 10-, 15-, 20- and 25-round capacities to fit a wide range of hunting, competition, and law-enforcement applications. Factory marked floorplate. Will only fit Armalite AR10 rifles, no other makes or models. Mfg: Armalite SPECS: Steel, Parkerized, matte black. Fits ArmaLite AR-10 chambered in .308/7.62mm. Will not fit the type "A" AR-10 designed for P-MAG magazines with an "A" serial number prefix.

more >>
Brownells
$39.99 See It
Armalite Ar10 50rd 308/7.62x10 Drum Magazine - X-10 50rd Drum Magazine

Rugged, reliable 50-round drum magazine designed for .308/7.62x51mm & .223/5.56x45mm, full metal jacket ammunition provides plenty of capacity and reduces reloading time. Rated for full-auto fire, the low-profile drum is still compact enough for shooting from the prone position. Integral hand wheel makes it easy to crank back the spring for quick loading/unloading. X10 fits Armalite AR-10 .308 and similar designed rifles.  Mfg: X Products SPECS: Aluminum, friction-reducing ceramic finish, matte black. 4¾” (12cm) O.D. 4.9 lbs. (2.2kg) loaded wt.  X10 fits Armalite AR-10 .308 and similar designed rifles.

more >>
Brownells
$275.00 See It
Ar-10® 308/7.62 Magazines - Ar-10 Magazine, 10-Rd

Brand-new, factory-made, Generation II magazines built by ArmaLite® feature a spot-welded, heavy gauge steel body that won’t distort when fully loaded and a contoured follower designed to ensure exceptionally smooth, reliable feeding. These aren’t converted M14 magazines, but mags purpose-built specifically for the AR-10 Type "B" lowers only - the same mags that come with new rifles. Available in 5-, 10-, 15-, 20- and 25-round capacities to fit a wide range of hunting, competition, and law-enforcement applications. Factory marked floorplate. Will only fit Armalite AR10 rifles, no other makes or models. Mfg: Armalite SPECS: Steel, Parkerized, matte black. Fits ArmaLite AR-10 chambered in .308/7.62mm. Will not fit the type "A" AR-10 designed for P-MAG magazines with an "A" serial number prefix.

more >>
Brownells
$34.99 See It
Ar-15/Ar-Style .308 Jpscs Silent Captured Spring System - Jpscs-10 Silent Spring System

Drop-in captured-spring recoil system helps your AR function more smoothly and quieter without any permanent modifications. The carefully balanced, custom-ground buffer spring, combined with the JP LMOS buffer, greatly reduces friction and vibration - say goodbye to the annoying “spoon over a cheese grater” noise of conventional springs and buffers. Fits buffer tubes for both M4-style collapsible stocks and also, using the included spacer, the longer tubes for fixed rifle stocks. The Auxiliary Spring Rate Kits for the JP Silent Captured Spring allow custom tuning of the device to a given rifle. While the default spring offers the best performance for the widest range of co Mfg: J P Enterprises SPECS: Stainless steel and hard polymer. 7" OAL. Nylon spacer – 1-5/8" long. Instructions included. JPSCS-15 fits AR-15/M16/M4. JPSCS-10 fits AR-style .308 rifles, including DPMS LR-308, ArmaLite® AR-10®. Does not fit Rock River Arms LAR-8.

more >>
Brownells
$137.99 See It
Ar-15/M16/Ar-Style .308 Low Profile Adjustable Gas Block - Ar-15/308ar Adjustable Gas Block .750 Set Screw

Adjustable gas block enables the shooter to fine-tune gas flow and rifle performance in the field. Designed to fit under free-floating handguards, the block secures to the barrel with two setscrews. Adjustment screw on the front of the block accepts the included hex wrench; a detent locking mechanism keeps the screw securely in place without the need for thread-locking compound, providing smooth and consistent cycling. Mfg: Syrac Ordnance SPECS: 416 stainless steel, Melonite coated, matte black. 1" (2.5cm) long. 1.34" (3.4cm) high. 1.7 oz. (48.8g) wt. Fits AR-15/AR-style .308 models with .750" O.D. barrels. Includes 2 gas tube roll pins, set screws, L-shaped hex keys, and instructions.

more >>
Brownells
$104.99 See It
Ar-15/Ar-Style .308 Jpscs Silent Captured Spring System - Alternate Spring Pack For Jpscs-15

Drop-in captured-spring recoil system helps your AR function more smoothly and quieter without any permanent modifications. The carefully balanced, custom-ground buffer spring, combined with the JP LMOS buffer, greatly reduces friction and vibration - say goodbye to the annoying “spoon over a cheese grater” noise of conventional springs and buffers. Fits buffer tubes for both M4-style collapsible stocks and also, using the included spacer, the longer tubes for fixed rifle stocks. The Auxiliary Spring Rate Kits for the JP Silent Captured Spring allow custom tuning of the device to a given rifle. While the default spring offers the best performance for the widest range of co Mfg: J P Enterprises SPECS: Stainless steel and hard polymer. 7" OAL. Nylon spacer – 1-5/8" long. Instructions included. JPSCS-15 fits AR-15/M16/M4. JPSCS-10 fits AR-style .308 rifles, including DPMS LR-308, ArmaLite® AR-10®. Does not fit Rock River Arms LAR-8.

more >>
Brownells
$37.99 See It
Ar-15/Ar Style 308 Cleaning Rod Guide - Ar-15

Replaces the bolt carrier, seals the upper receiver and provides safe and effective cleaning from the breech instead of the muzzle. Solid aluminum rod guide helps prevent throat and chamber damage plus, the rubber ''''O'''' rings keep bore cleaning solvents out of the lower receiver. Mfg: J P Enterprises SPECS: Machined aluminum, AR-15 - red, anodized finish. 10'''' (25cm) long. Fits .223 only. AR-10 - blue, anodized finish. 11.5'''' (29.2cm) long. Fits .308 only.

more >>
Brownells
$34.99 See It
Ar-15/Car-15/Ar-Style .308 Chrome Silicon Springs - Ar-15 Cs Buffer Spring

These flat wire, high-quality action/buffer springs from champion shooter David Tubb will perform flawlessly and are duty rated for 500,000 compression cycles at maximum performance. Made to “extra power” specs without the extra material, these springs are surprisingly lightweight, yet exttremely durable. Gives correct timing and resistance on the recoil stroke and a controlled rebound ensures reliable feeding with consistent forward thrust on every shot. Keeps the bolt locked a little longer to allow pressures more time to subside for perfect cycling. Mfg: Superior Shooting SPECS: Chrome silicon steel. AR-15 fits both fixed and collapsible stocked AR-15 rifles and carbines without modification to spring or gun. AR-10 .308-style fits both AR-10 and SR-25/LR-308 platform Rifles and Carbines with either rifle or carbine receiver extensions.

more >>
Brownells
$24.99 See It
Ar-15/Car-15/Ar-Style .308 Chrome Silicon Springs - 308ar Cs Buffer Spring

These flat wire, high-quality action/buffer springs from champion shooter David Tubb will perform flawlessly and are duty rated for 500,000 compression cycles at maximum performance. Made to “extra power” specs without the extra material, these springs are surprisingly lightweight, yet exttremely durable. Gives correct timing and resistance on the recoil stroke and a controlled rebound ensures reliable feeding with consistent forward thrust on every shot. Keeps the bolt locked a little longer to allow pressures more time to subside for perfect cycling. Mfg: Superior Shooting SPECS: Chrome silicon steel. AR-15 fits both fixed and collapsible stocked AR-15 rifles and carbines without modification to spring or gun. AR-10 .308-style fits both AR-10 and SR-25/LR-308 platform Rifles and Carbines with either rifle or carbine receiver extensions.

more >>
Brownells
$29.99 See It
Ar-15/Ar Style 308 Cleaning Rod Guide - 308ar

Replaces the bolt carrier, seals the upper receiver and provides safe and effective cleaning from the breech instead of the muzzle. Solid aluminum rod guide helps prevent throat and chamber damage plus, the rubber ''''O'''' rings keep bore cleaning solvents out of the lower receiver. Mfg: J P Enterprises SPECS: Machined aluminum, AR-15 - red, anodized finish. 10'''' (25cm) long. Fits .223 only. AR-10 - blue, anodized finish. 11.5'''' (29.2cm) long. Fits .308 only.

more >>
Brownells
$37.99 See It
Ar-15/Ar-Style .308 Jpscs Silent Captured Spring System - Jpscs-15 Silent Spring System

Drop-in captured-spring recoil system helps your AR function more smoothly and quieter without any permanent modifications. The carefully balanced, custom-ground buffer spring, combined with the JP LMOS buffer, greatly reduces friction and vibration - say goodbye to the annoying “spoon over a cheese grater” noise of conventional springs and buffers. Fits buffer tubes for both M4-style collapsible stocks and also, using the included spacer, the longer tubes for fixed rifle stocks. The Auxiliary Spring Rate Kits for the JP Silent Captured Spring allow custom tuning of the device to a given rifle. While the default spring offers the best performance for the widest range of co Mfg: J P Enterprises SPECS: Stainless steel and hard polymer. 7" OAL. Nylon spacer – 1-5/8" long. Instructions included. JPSCS-15 fits AR-15/M16/M4. JPSCS-10 fits AR-style .308 rifles, including DPMS LR-308, ArmaLite® AR-10®. Does not fit Rock River Arms LAR-8.

more >>
Brownells
$137.99 See It
Ar-15/M16 Flash Suppressor Die - 5/8''''-24 Thread Cutting Die

A must when threading custom barrels or chasing threads on standard barrels. Use to make custom supressors or clean up existing factory threads. Custom-made to factory specs. Mfg: Brownells SPECS: High-speed steel. AR-15/M16 - .500"-28 thread, 1.5" dia. body. AR-10 - 5/8"-24 thread.

more >>
Brownells
$25.25 See It
Ar-10® 308/7.62 Magazines - Ar-10 Magazine, 15-Rd

Brand-new, factory-made, Generation II magazines built by ArmaLite® feature a spot-welded, heavy gauge steel body that won’t distort when fully loaded and a contoured follower designed to ensure exceptionally smooth, reliable feeding. These aren’t converted M14 magazines, but mags purpose-built specifically for the AR-10 Type "B" lowers only - the same mags that come with new rifles. Available in 5-, 10-, 15-, 20- and 25-round capacities to fit a wide range of hunting, competition, and law-enforcement applications. Factory marked floorplate. Will only fit Armalite AR10 rifles, no other makes or models. Mfg: Armalite SPECS: Steel, Parkerized, matte black. Fits ArmaLite AR-10 chambered in .308/7.62mm. Will not fit the type "A" AR-10 designed for P-MAG magazines with an "A" serial number prefix.

more >>
Brownells
$29.99 See It
Ar-10® 308/7.62 Magazines - Ar-10 Magazine, 5-Rd

Brand-new, factory-made, Generation II magazines built by ArmaLite® feature a spot-welded, heavy gauge steel body that won’t distort when fully loaded and a contoured follower designed to ensure exceptionally smooth, reliable feeding. These aren’t converted M14 magazines, but mags purpose-built specifically for the AR-10 Type "B" lowers only - the same mags that come with new rifles. Available in 5-, 10-, 15-, 20- and 25-round capacities to fit a wide range of hunting, competition, and law-enforcement applications. Factory marked floorplate. Will only fit Armalite AR10 rifles, no other makes or models. Mfg: Armalite SPECS: Steel, Parkerized, matte black. Fits ArmaLite AR-10 chambered in .308/7.62mm. Will not fit the type "A" AR-10 designed for P-MAG magazines with an "A" serial number prefix.

more >>
Brownells
$29.99 See It
Ar-10® 308/7.62 Magazines - Ar-10 Magazine, 20-Rd

Brand-new, factory-made, Generation II magazines built by ArmaLite® feature a spot-welded, heavy gauge steel body that won’t distort when fully loaded and a contoured follower designed to ensure exceptionally smooth, reliable feeding. These aren’t converted M14 magazines, but mags purpose-built specifically for the AR-10 Type "B" lowers only - the same mags that come with new rifles. Available in 5-, 10-, 15-, 20- and 25-round capacities to fit a wide range of hunting, competition, and law-enforcement applications. Factory marked floorplate. Will only fit Armalite AR10 rifles, no other makes or models. Mfg: Armalite SPECS: Steel, Parkerized, matte black. Fits ArmaLite AR-10 chambered in .308/7.62mm. Will not fit the type "A" AR-10 designed for P-MAG magazines with an "A" serial number prefix.

more >>
Brownells
$34.99 See It
Search within results
  • Find by Price
    • $ to $