Union Nut, Quick Connect, PAC-FAB, Dynatron, 1-1/2"FBT, Blk ABS
Waterway Pump trap assembly. 6" in diameter. 2" FBT (female buttress thread / union nut) x 2" MBT (male butress thread). Complete with Basket and lid.
Valve, 1-1/2" S x MBT Thread and FBT Union Slip Slip vs. Spigot - Whats the difference?
AquaFlo 50100130 Spa Pump Union Adapter Kit that will allow you to turn your 1.5" wet end intake or discharge into a 2" intake/discharge. This kit takes the guess work out or the common question: "Is my wet end a 1.5" or 2" intake". The answer is easy. Purchase the 1.5" intake and this kit and you will have both covered. This kit includes the following parts: 1 - 50100130 1.5"fbt x 2" mbt Adapter Bushing 1 - O-287 1.5" O-Ring 1 - 711-4010 2" Flat Gasket
Union Complete, Pump, AMERIC, 1-1/2"FBT, Self Aligning Slip vs. Spigot - Whats the difference?
Union Assembly, one-piece, 1-1/2"FBT x 2"MBT
Pump Union, 3" Pvc, FBT Slip vs. Spigot - Whats the difference?
Union Complete, Pump, AQUAFLO, 2"FBT x 1-1/2"S/2"Spg 52203000 Slip vs. Spigot - Whats the difference?
The Hayward SPX1480C is a union nut replacement. This item is compatible with Hayward Self Align Unions and Perflex extended-cycle D.E. filter models. It also fits System III and Hayward Pro Series sand filter models.Please, check out the models you can use with the Hayward SPX1480C below.
The Hayward SPX1485B3 is a union elbow .This replacement component fits the Hayward Pro Series, S200 sand filter models. This replacement part is also compatible with System II and with Hayward Unions and filter valves model SP1486. This order is a factory original Hayward replacement...
The Hayward HAXNUT1930 is a set of two heater union nuts. This order is a replacement component. It is constructed for the Hayward H-Series heaters. The model is an original Hayward factory replacement part.
The Hayward SPX3200UNKIT set is for a TriStar and NorthStar pump union connector kit. This order contains a connector, nut and corresponding O-ring. This replacement part is designed for Hayward pool and spa pumps manufactured after 2008. It is a Hayward factory original set.
Jandy TailPiece, Cap & Union Nut Set
Free Shipping on Any Order over $99!
Porcelain Union - Porcelain Union Pun1 Handled Footed Nut Dish HC - Pink Roses, Yellow & Blue Border
Hayward 2" Union Nut
1.5" Small Flange split nut for pump union. They are made to replace pump union split nuts. They have a small flange, and are not for heaters assemblies. This split nut will fit most 1.5" pump unions. The overall diameter of the split nut is 2-3/4" and the flange side opening is 2-1/4". Due to the small flange, they will not fit heater union assemblies. Includes: 1.5 inch split nut, screws & the recommend flat gasket to help ensure a water tight seal. Note: The 1.5" is not the actual measurement but a representation of the inner diameter of the plumbing that is used.
2.5" Split nut for pump unions and 3.0" stainless steel heater housings. Commonly found on Waterway executive series wet ends and low-flow heater assemblies (Gecko M-class and Saratoga). They are made to replace pump union and heater split nuts. Measurements: Outer diameter- 4.0" Flange opening- 3-1/4"Note: The 2.5" is not the actual measurement but a representation of the inner diameter of the plumbing that is used.
Speck Pump Union With Nut and O-Ring 3"
Jandy R0327301 Tail Piece, O-Ring & Union Nut (Set of 2) 2" x 2" Tailpiece
Waterway Union Assembly 1"S Nut W/ 1"B Tail PC. & O-Ring